Chosen Solution When I try and turn my mixer off it keeps going back to the low speed. The lever (switch) keep popping back to on and will not stay in the off position. I’m suspecting a bad speed governor. They can be repaired, but figuring out how they work is tricky.
Chosen Solution Why when I print something it just comes out as a blank piece of paper Unfortunately, the steps you have already taken (1. replace ink cartridges 2. replace print head ) are the only economical fixes for this problem. The print heads on Kodak printers go bad often. These printers are advertised as economical to operate, but they don’t tell you about the print head problems. I have the same problem with a brand new Kodak printer, there is no one who will even try to fix his desk ornament…....
Chosen Solution I need the traction wheel bracket the bolt damaged everything I can find @cabrita it is a bit hard to find a part based on your description. Post some pictures of the part you need with your question Adding images to an existing question or check the attached parts list and see if you can identify the part on there. Let us know what you find. SR8855 parts list
Chosen Solution Why does it not pick up good? Also does not pick up cat hair Hi As with most vacuum cleaner they do need maintenance Have you tried cleaning the brush roll and washing the filters? That usually helps issues like this or you could fully dismantle the whole thing and clean it to bring it back to near brand new which is even better That’s what I do when I see issues with vacuum cleaners Hopefully this helps Any questions please ask Thanks:-)
Chosen Solution I removed the flex cable attached to the power button cable and tried to attach it to a new power button cable, but the cable broke. Should I buy a new flex cable? This one is for ApplePay NFC. If you don’t want that, you can ignore it.
Chosen Solution Hello, For quite a long time, I have been repairing an old PowerBook 140. The comuter had mnay issues with parts that I have mostly remedied with eBay purchases. However, I am still having trouble getting it to function completely. Whenever I boot up the computer, it gives my a grey screen and nothing else. When I use the reset buttons on the back of the computer, one of two things will happen - the computer beeps, makes a whirring noise (I believe it’s the hard drive spinning up), stops, and repeats the entire process again....
Chosen Solution Hello, I’ve done some research but haven’t found anything quite the same as my issue. I think there was some kind of power surge & when I try to turn on my iMac, it chimes but the screen stays black. The caps lock button lights up & if I hit the buttons to increase/decrease the volume, it makes the usual noise. The screen stays black but does have white flickering lines sometimes or almost the whole screen sort of flickers white, especially after you press buttons....
Chosen Solution The keyboard flex only goes in the connector until it stops - that is a zero insertion force connector - so no pushing or forcing. If you managed to scratch the carbon traces on the plastic flex it may not work properly - plastic tweezers can be a good thing if you are worried about damaging it. If you remove the blue plastic from the tip of the flex cable it will not be rigid, or as thick, and will not get a good connection / or work at all....
Chosen Solution My right AirPod is not working Hi, one AirPod no working is a common problem. Usually you should try to plug the case in and keep the AirPods in the case. Next I would try to disconnect them from your Bluetooth and try to reconnect while they are in the case. Then if they don’t work I would try going to your local tech co. To see if they can fix the problem....
Chosen Solution So I just got my phone back from a friend that had it for about a year I went to turn it on and everything worked fine right up until after startup After the logo screens disappear, the screen goes black and I cant see anything. It’s not the actual screen because when i hold the power button it shows me the options to power off and whatnot. I’ve already tried the hard/factory reset method and it dodnt work....
Chosen Solution My screen is cracked on the galaxy s5 the phone still comes on and make noises but cannot see anything on the screen …What part of the phone needs to be replaced ? The LCD Digitizer ?LCD Assembly? Help Plz Yes, replace the LCD screen just like that. Also you should notice that if the LCD screen comes with adhesive sticker, if not, you will need such a piece of sticker....
Chosen Solution So I spilt literally a droplet of water on the right hand speaker and the sound completely stopped working. I went to system > sound > output, and it says ‘headphones’ ‘ Headphone port’ ??? could anyone help please!! I would turn the laptop off and let it dry out, have a fan blow air on it. After a day, turn it on and try again. Under Sound> Output it should say Internal speakers, try and choose this one....
Chosen Solution I replaced the battery just fine but the new one will still not charge. The power cord and adapter are good. I/O problem or what else could it be ?? It looks like your logic boards charging logic has failed as your battery current charge is 2050 mAh, yet your charger is connected but not charging! Unless you only just connected the MagSafe charger and the logic hasn’t flipped the ‘Charging with’ and the value ‘0 Watts’ is also altered to a value....
Chosen Solution My iPhone 4s battery was, as you might imagine, not holding a charge like it used to. It held a charge for about a day and a half, so usable, but not ideal. I ordered a new battery through iFixit, and this is where my troubles started. The battery I was using before this new one was the third one I’ve used in this phone, so it’s no stranger to having batteries swapped, and yet for some reason, upon swapping in the new battery I began experiencing random crashes....
Chosen Solution Hi, the question is pretty eloquent. This tablet came perfectly fine but needed a new SD connector. I replaced it and I don’t know what I messed up but backlight Is gone. Ive tried replacing the backlight connector, I’ve compared multimeter readings across the board with another mb, I can’t pinpoint the issue. The EMMC got pretty hot because I forgot to remove it, also I lost and then resoldered a capacitor near the diode in the other side of the board (I was heating up from the back in that area to install the port since it’s a plastic connector and I burned the first one before I could solder it....
Chosen Solution turned on my Sony bravia 42" tv and immediately the whole scree was covered with vertical lines about a pixel or two in width. the color of the lines changed as the image changed. Could it be that the firmware got clobbered and is there a way to reload the software? Had a problem with my 52" Sony years ago and they sent me a thumb drive with a software update that fixed the problem....
Chosen Solution I have an Ez-go PDS. My forward/reverse switch is a dash mount. When I select reverse, my beeper comes on but the cart starts to engage in reverse but doesn’t move. Forward works fine. Any suggestions? If yours is like mine, under the seat is a large (~12” x ~8”) plastic cover, held on by 4 bolts. Upper 2 are easy, lower 2 aren’t. Inside are the power and reversing relays....
Chosen Solution Hello. My phone has been off for 2 days, fully charged it. and when i switch it on it ready no service… Cannot make calls nothing. Re-started still noting did Factory reset.. Still nothing. Please help!!! Thanks check the SIM card is working properly Check with your operator whether your IMEI blacklisted or not update the firmware if available via OTA Change the network mode : GSM only if signal comes change the network mode to 3G only if you found same issue the one of transceiver not working properly huawei p7 wifi not working...
Chosen Solution Why don’t I get any sound when I get a text Hi, If it is only SMS messages where there are no notification sounds and you are using the default Message app, then go to Home > Messages > tap right hand key below screen to bring up options menu, select Settings > Notifications. Ensure that Mute is Off and that you have selected the sound of your choice in Sound in lieu of none if none is selected....
Chosen Solution I was brought an iPad 4 CDMA with a broken display. I ordered a replacement and when it arrived I installed it. Everything went good with the install but there was no touch. I tried disconnecting and connecting it a few times and it did not help. I then hooked up the original broken display and everything worked so I called iFixit and they sent out a replacement. When that one showed up I installed it and the same thing happened, no touch but the original display works....
