Chosen Solution The on/off button on my Ipod nano is no longer “raised” so that it can be pushed to turn the ipod on (or off for that matter). Can this be fixed? I have exactly the same problem with the on/off switch on my nano 6 gen. I don’t understand why you say it has been out for less than a year??? I got my nano 6th gen at the beginning of 2012, that’s 4 years ago!...
Chosen Solution only filling a half a cup @shelton19 check this guide for the same issue. Clean the tubes leading from the K cup holder with a pipe cleaner, then fill the reservoir with white vinegar, run your machine through the reservoir and fill with fresh water, run this through to clear the vinegar. Mineral deposits build up inside the machine and limits water flow. The vinegar dissolves these.
Chosen Solution I tried to burn a cd, but the optical drive did not recognize the disc, and did not eject it. Now it is impossible to remove the disc from the drive. I several times switched the system on and off. No result. Please help. Thanks. Restart and hold the mouse button down to eject a disk. There are a lot more remedies if you need them, just ask....
Chosen Solution The over appears to be cooking at 25-50 degrees higher than the temp the oven is set for. How do I calibrate? Hi @rchill4 , The oven may be operating within its specified parameters or marginally just outside them anyway. According to the oven calibration section on p.2 of the service data sheet for the oven (see 790.7105 model in list), at 350°F the acceptable temperature range is 330° - 390°F....
Chosen Solution Unless I have bluetooth/plug-in headphones connected, when I attempt to make a call my phone restarts. The volume buttons and mute switch are not functioning either. When I take a picture with bluetooth/plug-in headphones it works sometimes, but then it restarts a few seconds later. When I consulted a private phone fixer, he said the cost could total $200 (including repairing the screen and back-case since my front camera is cracked)....
Chosen Solution To give a bit more detail I have an iPhone XS that doesn’t always turn off but every so often when taking photos will cause it to shutdown even if it has battery it then won’t turn back on until you provide charge (like a jump start) after receiving a brief charge it comes back to life and doesn’t do it again for a while. I can replicate it if I take sometimes 10’s of photos sometimes 100’s....
Chosen Solution WhIle my tv is turned on it perodocally clicks or pops. Other than the clicking it works perfect and nothing happens when it clicks. It just has an off and on click. It doesn’t happ er n all the time but it is annoying when it does. Anyone know what may be causing this to happen? ladylyn7 clicking is usually related to relays on the power board. Since you do not have any issues and your TV continues to work with failure, I would wait for things to actually stop working....
Chosen Solution I have a LG TV 55lw5600 power light turns on but no picture or sound Johnny Diaz first unplug the power cord, wait for 10 seconds, and then plug it back in. If the status LED is lit, try to turn on the TV using the power switch on the unit, not on the remote. If that does not work remove the back from your TV (after you unplug it)....
Chosen Solution NXP Power Management IC Chip is greatly warmed. I changed it to a new one, but nothing has changed. What else can make it warm? What is the maximum temperature of the withstand this chip? I am afraid that I was overheat it. Tth(die)………. die threshold temperature is 125c Tamb ……….. ambient temperature is min -40c max +85c Tstg …………… storage temperature is min -55c max +150c check the Apllication information for the PCF50633 this is the correct name of philips NXP PMIC...
Chosen Solution My Brother MFC-3240C is not printing. I have not used it for a few years. I’ve run the clean 5 times and my black level indication has gone from full to minimal. The printed page has no ink on it what so ever. What do I need to do to get this working? Thanks @marklk , Mark, I do not own this printer. Probable clogged print head. Remove the print head if able and soak it in 90%+ Isopropyl Alcohol....
Chosen Solution My PS4 is not turning on it just beeps once and shuts off immediately. Tried almost all troubleshooting methods on the sony website. Method 1: Reconnect the power cable Reconnecting the power cable can power reset your PS4 and clear the corruption issues on your console. This is the first thing you should try when your PS4 can’t turn on. 1) Unplug the power cable from your PS4. 2) Wait for at least 30 seconds....
Chosen Solution my power will not turn on the camera even with new batteries @roovb2000 always check the battery door first. If it does not close properly your camera does not get the power. You also did not tell us if this camera worked before you changed the batteries or if there was any prior damage. ‘‘‘Camera does not power on ‘‘‘When the on/off button is pressed the camera does not turn on ‘‘‘Low battery ‘‘‘If the camera does not turn on, check to see if the batteries are low....
Chosen Solution My sound is very low and the external speaker jack doesnt work This may seem obvious but have you tried turning up the volume? If you include more details I can try to give you more help.
Chosen Solution This power adaptor was powering TSC ttp 244 plus label printer. Power cable is ok, green LED not working, how to go about checking whats wrong. Hi @harinderdivine, You need to check where the active leg of the input connects to first. Usually it connects to a fuse or a MOV surge suppressor and then since the output is DC there will be a diode stack to convert the AC to DC....
Chosen Solution Hey Guys, Trying to source these replacement parts but unsure as to what to search anyone found these parts and their correct naming? Thanks in advanced The first one is a sim eject pin but used to be called the sim eject lever on older models. I have only seen this part included in small parts kits sold on eBay for $7 or so. The second pic is called the wifi flex to charging port transition flex and is available from most parts suppliers....
Chosen Solution Hi, Somehow my power button (outer metal button) is lost.The inner power board is working fine. How do i get one? You could look for a “parts queen,” or a broken phone with parts that you can use, on eBay or elsewhere.
Chosen Solution Installed a new Western Digital ATA 5400 RPM 160GB hard drive, but new drive does not show up in disk utility to erase and format. Checked all the connections twice, but still doesn’t show up. Any ideas? Could the new HD be bad? It should be able to recognize the drive even if the formatting is wrong. If you’re positive you got the connection right, it could be a bad drive (I’ve had DOA drives before....
Chosen Solution Hi everyone, my nexus keeps trying to start then gets up to the google screen and then just keeps trying to get past that point but cant…. Is this a sign the battery is knackered? It does still charge tho so not sure if a virus has buggered it or what??? Any help would be appreciated Cheers Ally If you have charged it all the way, and it still fails to try to get past the Nexus logo, it could be a battery issue....
Chosen Solution I have a LG 55lw5600 that’s has no picture. It also has no backlights when powered on. I found a service manual online and started checking voltages. From the tests I have done so far I can tell the smps is good and the inverter is good (by tests that use jumper wires), the led lights come on during this test when ac power is applied. I have done the flashlight test and see nothing....
Chosen Solution My Sony T2 has WCDMA on sim 1 and put GSM on sim 2. Sim 2 loses network coverage completly. this is the same when I do it vice versa e.g. sim 1 -GSM and sim 2 - WCDMA/GSm preffered, then sim 1 loses coverage, seeing as the phone is designed to work as one sim on WCDMA and the other on GSM, whichever slot thats has GSM has no Network completely....
