Chosen Solution Yellow appears to not be used in the printing process. I have changed out the cartridge and no improvement. Paper settings are correct. Print looks nothing like the preview. it’s possible that the printhead might be clogged, try flushing it out https://www.youtube.com/watch?v=IszUNL7z…
Chosen Solution I’ve just completed the screen replacement for my phone and when i tried to turn it on; nothing happens, no vibration, not lighting screen nothing. I don’t know what to do, could someone please provide me with either an explanation as to why this is happening and a solution. I’ve checked the cable and its not cut or broken. Sounds like your connection for the screen may have come loss during reassembly....
Chosen Solution I’ve got a ranger 2900 cb it transmits ok and receives ok but if I knock it or it falls forward on the bracket it goes off what can this be please Sounds exactly like you don’t have a good ground or power connection, it may be possible that the wire connector has a lose contact to the main board where it is soldered from the wire to the board but I think you have a lose connection first before digging into it....
Chosen Solution I can’t use sim card on my phone it says not registered on network Is the phone locked to another network? Has it been sim locked? What does the network provider say about the sim?
Chosen Solution I ordered A Sega Game Gear Of of Ebay The photo Showed the game gear was in good Working condition But when I received it i Was horrified to find out that it was jostled so hard in shipping (the Seller Did not Know Anything About packing retro handhelds) he screen only worked correctly when i tilted it downwards a bit.Plez Help It is likely a screen capacitor problem, you can google it to find out more....
Chosen Solution My vacum will run for a few seconds when I first pull the trigger and then it starts cutting out If your Dyson v6 Absolute vacuum cleaner unexpectedly turns off during use, see the Dyson v6 Absolute Shuts Off While In Use problem page for possible causes and solutions. If your Dyson v6 Absolute vacuum cleaner’s battery life is not long enough to complete a vacuuming task, see the Dyson v6 Absolute Battery Life Is Too Short problem page for possible causes and solutions....
Chosen Solution Please help me to repairing my wifi connection and Bluetooth You can try to resent the phone in settings. If it dose not work then you can call Apple and they should be able to help you to fix your I phone. Good luck.
Chosen Solution So, I just got done fixing my 3DS however it appears that It won’t power on, it doesn’t make any noise, or do anything, the power button goes on for a bit, and then just turns off, the only thing not connected are the speakers (broken ribbon cable connector) From my personal experience this happens from the camera flex not be connected 100% but it really could be from really any connector or flex being damaged, I mean did you try to flip up any of those connectors while you were in there?...
Chosen Solution On a USB Ammeter it displays 0.46A and constantly stays there. Opened up device and found battery was pretty much flat. Charged it up around 3.7-4.2V and attempted to turn it on with the battery connected once the battery was charged up externally at that voltage. It still did not turn on and charger still reports 0.46A. No signs of liquid damage on board as inspected under microscope. I would suspect charging chip but isn’t it supposed to turn on with a charged battery if that was the case and not charge?...
Chosen Solution I need to replace Roblox / CENTER DASH BEZEL W/ STORAGE & AC VENTS OEM of my Nissan Sunny 2004 Model. I want to verify that 2000 - 2006 NISSAN SENTRA and Nissan SUNNY this component are same /compatible. I can fix this Nissan Sentra CENTER DASH BEZEL W/ STORAGE & AC VENTS OEM to Nissan Sunny 2004 Model Soji mathew that is a different question to answer since it would require us to see the parts side by side....
Chosen Solution I just replaced my Lightning connector and it works great, but now my cell service does not work or it goes in and out every few seconds. I rechecked to ensure the antennas are connected properly and they are. WiFi works fine. Any ideas? Any little peices of metal shorting put did u use the right screws in the right places did you remember to turn off your phone do u usually get good cell service where you are?...
Chosen Solution I few months ago, i have a battery problema. It stuffed and pull off the botton and the screen. I manage to find the battery (AP00069) and sucessfuly change it. The watch recharge properly and when I turned it on, I can hear the sounds of messages coming, and vibration when it does, but no image whatsoever. I tried to disassemble it again, and check more carefully the flat cable connector between the screen and the motherboard....
Chosen Solution Late 2013 MacPro with CPU, RAM, and SSD upgrades. Not my main machine. Just realized that the serial number does not show up. Other than this, the machine runs perfectly. Apple Store offered to replace the logic board in order to be able to use their serialization tool. The logic board is the original and is otherwise fine. Any ideas on how to flash the board to reset the serial number?...
Chosen Solution I am following the guide for front panel replacement and have so far managed to free the screen from the glue. My problem is the guide has a warning (below) about the battery isolation pick procedure, which it says is outdated - can anyone advise of the new / preferred method or point me to a resource that can help? “The battery isolation pick or battery blocker is an outdated way of isolating the battery, as you risk damaging the battery pins underneath the logic board....
Chosen Solution When printing, just as the paper begins to exit into the tray, the paper jams. It wrinkles the leading edge of the paper. Took it to local repair shop and they thought it was a fuzing issue, but couldn’t say for sure less than $118. charge. The fuser is the likely suspect and it is possible that the roller is bad. If the printer has had labels put through it then the likely issue is the glue has got onto the roller hence the jamming....
Chosen Solution The percentage charge on the battery of my Samsung Galaxy A3 (2016) is decreasing, rather than increasing whilst charging (it does so worryingly rapidly, even when on battery saving mode)- the only time it doesn’t decrease, and the number remains completely stationary, is when the phone is shut off. I’ve tried three different USB cords and plugs (two chargers were fast-charging and by Samsung, the other was not) and multiple different wall sockets, so I know that those options have been eliminated....
Chosen Solution So the title says it all basically. The phone fell into water, was taken out in a matter of seconds. Kept working, so I just let it be. Sometimes the power off menu would pop up by itself and after twenty minutes of working normally, except for that anomaly, it just turned off and started rebooting. I just took out the sim and put it into rice. Is it a lost cause?...
Chosen Solution Hi, well I woke up this morning and my cell phone was off so i tried turning it on and nothing. I tried leaving the battery out for 10 minutes but it wont respond. Please helppp :,( Hey Giada. Here are a couple of things you can try: -Replace the battery but with device off. -Remove the battery. -Press down on the volume up and home buttons then press the power button for about 4-5 seconds....
Chosen Solution If you have a computer Unplug the cable from the power charger. Check that your computer is on and connected to a power source. Connect your phone to your computer’s USB port with the cable that came with your phone. Wait 10–15 minutes. Disconnect and reconnect the cable from your phone within 10 seconds.
Chosen Solution So I just replaced my Pixel 6’s screen via the IFixIt repair kit (btw, this was way easier than expected, so that’s a win). However, I can no longer use the fingerprint reader. If I go to set it up I get an error message: “Can’t use fingerprint sensor. Visit a repair provider or g.co/pixel/fingerprintunlock”. That website was seemingly irrelevant and definitely unhelpful :). Ok, so I fixed this....
