Chosen Solution So I got my phone screen and back camera fixed last week, and ever since I got it back it has been acting weird, For starters, Touch ID won’t work. Every time I try to set it up it says unable to complete setup or something like that. Also FaceTime won’t work at all. It just says authenticating forever. Finally I have this weird iQT app now and from what I understand I shouldn’t have that....
Chosen Solution the plug, (socket) on back is faulty i think, because the cable wont plug in securely so gps keeps coming on and off, power. I had this same problem I removed the board and heated it to reflow the solder then reasembled and all was well. Heated it with a heat gun at the port and used heat dissipation tape around the port to protect everything else joe, if the cable is no longer properly fitting the usb port, you most likely will have to replace it....
Chosen Solution i cant find the pin out for the Power button flex. can someone highlight the two leads for the power button? im trying to diagnose a phone that wont turn on, but i dont have a spare button to compare it to. thankyou. 1 xxx xxx x2x 1 + 2 =power the top pin and the bottom middle pin… use the volt meter on continuity mode and click the button until it beeps while you are pressing it !...
Chosen Solution I tried to turn on the camera today and the button got stuck and won’t come back out. How do I fix this? Open the device using our guide and check to see if there is anything under the button. If there is, remove it or replace the button completely.
Chosen Solution I took out the old camera assembly to put on a new screen, but the two sensors (ambient light and proximity sensor) will not click back in no matter what I do, so I can’t put the earpiece speaker back on. Must be 4 reasons for that cause 1. Dust on your screen hole where proximity sensor aligned 2.Flex cable is damaged 3.Front camera connected deformed 4.Proximity sensor circuit demaged So to figure out the source of your problem first take new camera if does the same try to test it while the camera is out from LCD/Display let it free from obstacles because proximity sensor do sense near objects,if no solution try to do cosmic inspection on front camera connector (it maybe deformed during disconnect front camera)…....
Chosen Solution Ps4 beeps then turns off, have tried the washer fix, What should be my next step in attempting to fix the ps4? Thanks all! Hi koolgaming83, I suggest looking at this link PS4 beeps once then turns off. I hope something in here works for you. Good luck! Jasen Buy an Xbox one X and your problems will be solved. My ps4 does this as well has anyone found a solution to this?...
Chosen Solution I was trying to flash twrp for my Samsung galaxy tab 3 using TWRP manager app downloaded from play store.I got some error in between,and it asked me to reboot, Since then it has been contionously looping. I am not not able to enter download mode or recovery mode using volume up + power + home buttton,tried all the combinations, nothing seems to work. And also when my phone boots up,i see a red excalamation mark at top left,can someone tell me what does that mean and how to fix my phone....
Chosen Solution My sister was playing around with my phone and she purposely threw it until the whole screen fell off. This phone is the last gift from my late grandfather..Please, someone help me.
Chosen Solution I replaced my screen on my iPhone 6. The keys Y and the ) key don’t seem to work. When I press either of those keys I get the keys beside it. Any suggestions? - Tom This is either bad screen, or (more likely) a teeny bit of some kind of plastic or something stuck on one of the pins of your digitizer connector–either on the board or the screen....
Chosen Solution The Nespresso machine turns on and heats up, then on, no coffee flows. Typically, a tube is blocked, or the pump isn’t working. googling “Nespresso Innissia repair” yields lots of results
Chosen Solution I replace the blade SSD, RAM, and 3.5 with a 2.5 SSD. I did a full tear down following the guide by iFixit. I rebuilt the machine I followed the guide in reverse. When I first applied power I got three system beeps. I looked up the beep codes, the RAM that I installed was not seated correctly. When I fix the ram issue, I applied power back to the machine....
Chosen Solution My T100TA has been habing trouble turning on. I popped the lid, unplugged the battery and left it unplugged for a good 45 seconds to a minute. Put it back together and I plugged it in overnight and now its white (leads me to believe the battery is ok). The white power LED still flashes 5 times even though,from what ive read, Ive performed a hardware reset. I will detail what Ive tried....
Chosen Solution Locations of oxygen sensors on a 1996 chevy c1500 5.7 @symphony2627 best to see and to get to with the vehicle on a lift. Oxygen sensors bank 1 is any sensor upstream the catalytic converter and bank 2 is downstream. you’ll have one before and one after the catalytic converter. Even so the attached image shows a dual exhaust it also applies to single exhaust but will of course only have two sensors....
Chosen Solution My iPhone would flicker and become unresponsive occasionally- it would fix itself eventually and I could use it for up to a day before it flickers again. However after powering it down in order to try and fix the flickering, my phone won’t boot up. When I force restart my phone, a pink line appears for a second, then the screen goes blank again. Does anyone have any suggestions?...
Chosen Solution So I bought Devon a brand new PS4 pro as a Christmas gift 18 days ago.. it has worked perfectly up until last night/this morning. Devon was playing sonic & the game just froze so he unplugged & hooked it back up. Now when he tries to turn the system on the blue light of death light flashes & the tv says no signal. I’ve YouTubed & googled every trick & nothing works....
Chosen Solution I had plugged my kitchen aid classic mixer into 220v instead of 110v. It started running of full speed from the second use. Now even after plugging into 110v it runs in full speed. Sounds as if the little electronic phase control board has had it. You can find one on ebay (make sure it is for 110 volts). The Service Manual can be found at: https://www.google.com/url?sa=t&source=w…
Chosen Solution I have a ps4 slim and I took it apart a while ago to clean it and now the power button is jammed. It’s it wiggly and doesn’t click. I’ve been turning it on by the disc button but yesterday I took it apart again to try to fix the power button and now it won’t even turn on anymore and I cant insert a disc into my ps4 there is like this black plastic piece that is block the disc entrance....
Chosen Solution What could be the reason my Epson WF-7620 will print a test print bot it will not print from a computer or copy anything? Are you getting any error messages on the printer? What happens when you try to print or copy? Are you printing using a cable or wireless connection? If wireless, which method are you using? Any error messages on the device you’re printing from?
Chosen Solution Hi. My phone was on the roof of my car. I forgot to take it. When I was driving, my phone fell from my car roof and collapsed to ground with a high speed. My phone had screen saver and when I took it’s screen saver, I noticed some fractures . When I pressed power button, home button and volume down button together, I just felt a vibration but my phone screen didn’t turn on....
Chosen Solution Hi, after using my GT-N8010 for some years I realized my battery had to be replaced (long charging time, short duration full load). So I got a Patona 3104 SP3676B1A to replace the original battery (I’m sure it fits for this model). After the replacement I have those problems now: The tablet will not boot by pressing the power-button - nothing happens.There is no charging indication when I plug it in (PC or charger)....
