Posts

Chosen Solution My power button when pressed shows light but it doesn’t turn on the camera what should I do? Same problem ? Nikon COOLPIX S3600 Troubleshooting

Chosen Solution Some water entered the speaker while it was on my patio and now it won’t turn on, what should I do? The best choice would be to disassemble the speaker and thoroughly dry the motherboard and any other electrical components. A disassembly guide can be found on the device page.

Chosen Solution Hi there, I have a Macbook Pro here with water damage. I am unsure of the specs except that it is A1278 9,2 It was dried with rice. At first it would switch on… boot as normal but my password would not be accepted, when i tried to recover password using the recover with apple ID option it would crash. I removed the HD. I am trying to do the hardware diagnostics with d/alt-d but no luck....

Chosen Solution As above, instruction manual…..how do I take the top of my dryer off to access the door switch ??? Remove the two screws that attach the lint screen. Don’t drop them down the lint shute. Put a thin blade blade between the top and the front panel and pry up gently. This will release the clips on the front part of the top and allow it to pivot up on the hinge at the back....

Chosen Solution I need a transmission for an 88’ F150, automatic, 3 speed, 4x4, 350 motor. What do i need to find (or see when buying) in order to make sure it will go in my truck. Go to www.rockauto.com to find what ytour looking for Well make sure the bell housing bolts match the pattern of tranny and ujoints match. And the shifters are on correct side if there in a transfer case make sure it matches the bolt pAttern too they useally have a 203 or 208 transfercase on them

Chosen Solution Can anyone help. My keyboard and trackpad have both stopping working so can’t even enter my password. Have tried to link external wireless keyboard but no joy. I suspect it’s a software or working memory issue, but that’s just a guess. Tried to decrypt. Tired to press the alt button 5 times…. But no joy. https://thenextweb.com/lifehacks/2010/12… Try to reset your PRAM and SMC. Also, try using a wired keyboard or mouse to see if those work if the SMC and PRAM resets dont

Chosen Solution My phone battery was not working. So I replaced it with a new one. but when I started the phone it is just showing low battery but it is not charging and remain on low battery signal. I again open the phone and noticed there are some screws missing. Is there anything to do with missing screws or any other problem?? It is a common problem of new battery, not charging and low remain....

Chosen Solution Hi , I Have Google Nexus 7 brought in 2013, Recently my touch screen not working due to screen got broken. I just need information about changes for repair or replace the touch screen. Regards, Naresh Screen and digitizer (part) Screen replacement guide

Chosen Solution When I turn on my headset everything loads except the display. Hearing and tracking is fine but I can’t see anything. I know my computers not the issue because I tested it on a friends computer. im having this issue too, started when i put the visor down after typign on my keyboard. immediately lost sight and it was tracking perfectly. based on what ive dug up it seems to be the cable....

Chosen Solution I have an old 60 gb PS3, and I am new to electronic repair. I do know a few things and know how to read electronic blue prints. So I’m not completely clueless. My problem is my game system does not get power after the power cord. And I do not get any lights either. I am getting power to the game system and I have checked the power cord using a DMM to verify the cord is good....

Chosen Solution Vizio E480i-B2 After a recent power outage, the TV would just not power on, either from the power button or remote. I’ve tried holding down the power while unplugged—didn’t help. While testing the power board, though the fuse is not blown and capacitors look fine, I’ve noticed a few diodes with continuity with both polarities (shorted?). I’ve marked them red in the picture directly below. The standby power mostly hangs at ~3v, but it fluctuates(bad capacitor?...

Chosen Solution T-Con pcb did not fix this problem. I still have this problem and now no image at all. @bwebs blue tinted screen are usually not the result of a failed T-con board. It is usually related to bad backlight LED’s. You changed the T-con board and now nothing the set is dead or do you have works any sound. Give us more details about your TV. Things like what it does still do are important....

Chosen Solution how do i open the microSD card slot cover? from what i have seen of the tablet, there should be a panel by the volume buttons that has a small nook to get your finger nail under. Simply maneuvering this up and out should give you access to the SD card reader. it should be simple mechanical manipulation to get it out. clips and gaskets are all that hold it in place....

Chosen Solution Hi, im repairing my old ipod Classic thin six generation who has a broken model MK1634GAL Hard drive, i want to change but thata current version is too expensive, does anyone knows which options are to change that model?… it doesnt matter if it have a lower capacity (80-120 gb) aurzuah there are no real cheap options here. It will all depend on how much you are willing to spend....

Chosen Solution I have a ZTE N800 How can I open my phone when I get continuous popups of: Unfortunately ___(fill in the blank) has stopped? I’ve held the volume down and power to reset but it shows up as soon as it opens and I can’t get around it. Does this mean I should stop the run around and just get another phone? Thanks Hello Karla, Try booting into your phone’s BIOS before it fully starts up....

Chosen Solution This is a weird one. I have an iPhone 5S. I pick it up, press the Home button to wake it up, and the phone wakes up (asking for the unlock code) and vibrates. This happens regardless if the Mute switch is enabled or not. However, if I put the phone on a desk and press the Home button to wake it up, the phone wakes up and DOESN’T vibrate....

Chosen Solution My printer has been acting up and saying that the paper is out and to load more paper. However, there is paper in the printer. The printer can’t get it feed through and actually print. I can hear it try to grasp the paper when trying to print. How can I fix this? Make sure that the part of the paper tray that moves is in the correct position and clicked in....

Chosen Solution Hello, I have MacBook Pro 2020 A2251 and I have problem with screen brightness after updating to 12.5. Screen seems around 40% bright at setting for brightness on max. Also since updating keyboard is not lightning up and I can not change setting manually (if I move bar manually it just drops back to 0). Will be happy to hear any suggestions and how to resolve issue. Also I have tried to reset PRAM witch helps with screen brightness but after logging in account screen brightness returns to around 40%....

Chosen Solution Ps3 is not reading video game discs and is making ejecting sounds movies work I have allready tried tilting it up and that dosent work please help me and thank you Hello, you’re watching DVD oder Blu-Ray movies? And are you using the fat or slim modell? My old 60GB fat modell had an similar problem. I can’t play PS3 games but DVDs. After an firmware update it worked again....

Chosen Solution Hello there, I’ve had problems using the controller and the wifi with my Ps3 slim ever since I bought it. The controller is not recognized at all, but the WiFi is recognized but cannot connect. I opened the console today and checked if the antennas are connected correctly. Unfortunately this was the case. Do I have to replace the antennas or the chip to fix it? Honestly, replacing the antenna’s would be a good place to start....