Chosen Solution I took my phone to a repair company to fix my cracked screen. At that time,that was the only problem i had with my phone. After the repair i noticed my proximity sensor only works every 3rd/4th call. Took it back and they checked it and according to them, it was fix. It still does the same thing,but now after they worked on it again,my ‘up’ volume button and my accelerometer is not working....
Chosen Solution ps4 appears to be shorted out. the on/off button does not function to start the ps4 machine. what is the cost of repair upon me walking into your store with my ps4? thank you! david r. craft Since I don’t know where you are located, I doubt that you will enter my store, but… If you have no activity at all with this unit, start by replacing the power supply....
Chosen Solution my computer ah was jostled and broken, and the power port got liquid on it, hasn’t worked since and the computer is out of battery. the guide for MagSafe replacement isn’t for my model Hi, There is a guide ( MacBook Pro 13" Retina Display Late 2013 MagSafe DC-In Board Replacement ) And also the part (but it is expensive $59,95) MacBook Pro 13" Retina (Late 2013-Early 2015) MagSafe 2 DC-In Board Just in case: did you try charging with another charger, does the mac turn on, are you sure it is the MagSafe port?...
Chosen Solution What reasons are there for my pto clutch starting up and running fine for about 5 minutes then the blades just stop . I put a new pto clutch on and still same problem . Any help would be appreciated. John Deere L120 Renato Gonzalez since you already replaced the clutch and it started to do the same thing again I would focus on the wiring to the clutch....
Chosen Solution Is there anyway to fix this, I know I could probably clean underneath the trackpad but how in detail would I need to go to fix it myself, because I am strapped on cash because of everything that is going on. Thanks for the help in advance! Hi @dev0 , Here’s the service manual for the laptop, taken from this webpage. Go to p.45 to view the necessary pre-requisite steps and then the procedure to remove/replace the touchpad....
Chosen Solution My vw passat stopped showing outside temps —–C In the middle of your dash? What does it currently display? There’s a up/down button on the end of the wiper lever that scrolls through the menus. You should find temp eventually. I have the same issue and the AC is not working well. The temperature just shows “__ F”. I have replaced the ambient air temperature sensor, but still do not work....
Chosen Solution I just bought a new Xbox 360 controller. I want to sync it with my console. But the moment I turn on the console it is asking for a System Update. I can’t select either option of yes or no choose as I don’t have my controller connected yet! Pls help!! This is very tricky since it would be hard to connect your controller before the “System Update” screen pops up....
Chosen Solution Purchased new in 1984 and has been in storage for the last five years. Thought I would hook it back up. Connected the speaker cables to the back of the unit, turned it on but no sound. FM tuning was on full strength signal, checked out all control settings, everything was as it should be. Anybody have and ideas why I’m not getting any sound out of the unit?...
Chosen Solution When pluged in , it states not ready and then it turns off after a few minutes. This did not come from me, but I had the same problem: Chloe Simms, has gave information about this problem, and it has worked for several people.. Hope this helps. Check and see if you have enough water in the reservoir. If the problem persists, you may have a clogged exit needle....
Chosen Solution On the logistic board LED #1 is ON , but LED #2 Blinking , fan spin on a couple seconds and turn off, what is the problem can be? I’m suspecting your power supply has failed. Here’s the needed part iMac Intel 27" (Late 2012-2020) Power Supply Here’s a breakdown on the LED’s LED Functions: LED #1 - Indicates that the trickle voltage from power supply has been detected by main logic board....
Chosen Solution The smartphone works fine when without the Sim card. After inserting the Sim card, issuing the Pin code, the phone accepts the pin and then shuts off. Tried with other Sim cards, same result. Reseted to factory defaults, same result. Looks like a gsm network ploblem. There is always the X red in the network top indicator. Appreciate some help. i have the same problem try to use the phone test settings with code (##4636##) the go to the radio opption turn it off for about one minute then then turn it on after restart your phone ,hope it will help contact me through my email for further help jamesnehemia4@gmail....
Chosen Solution Accidentally dropped phone in the sink when water was still in there. The back is cracked badly to exposing the microphone and shield covering the lightning connecter. I am afraid water may have seeped in and damaged the components. I put the phone on the charger, it turned on for a second then it turned off indefinitely. I have tried holding the power button for a minute but it did not turn on....
Chosen Solution Icke Bong this is not liquid damage. this is damage from getting heated up. Most likely based on a short circuited component or connector. We would need to see some better pictures. Something straight on and nice and clear would be perfect.
Chosen Solution Hi there, I have done it, is set a supervisor password on my portege x20w (why not what can go wrong) and like all my passwords, i forgot it… My first instinct was to reset CMOS but, no battery to do so… Does anyone know how to reset the password since now i cant even boot it anymore Regards Mx Try this… Entering BIOS in Toshiba Portege Turn off your Toshiba computer....
Chosen Solution While trying to clean the internals of the machine, the power button switch snapped off of the board. Any way I can solder the button back on or jumpstart it before ordering a new board? Thank you so much for your help. Dear Jeremy, please I have the same problem too. What parts of the button did you solder back to the board. Please help, thanks.
Chosen Solution So, I found an old DS in my house that was broken for a while. Every time I powered it on, the green light on the “middle” part of the DS turns on, the bottom screen flashes white. Then, the green light changes to orange and quickly shuts off. I believe there may be a loose connection near the part where the top and bottom display connect. The only way to actually get it to work is to push back the top display really hard....
Chosen Solution I just replace my toner in my HP Laserjet 4050 but it will not print anything, there is no error , even printing a test page, only blank paper comes out. Is this a fuser problem? You could have a bad cartridge or did you forget to pull the toner tab? Review the troubleshooting steps in this manual: HP Laserjet 4000 & 4050 Service Manual
Chosen Solution When I try to switch from av to hdmi nothing happens only black screen although ps3 recognizes a hdmi connection… I ve tried with same tv hdmi port and cable to another ps3 slim and all worked perfectly..i reset video settings etc but no luck..any help? Have you tried holding down the power button when you have your video input in their. That usually works :)
Chosen Solution Hi, I have 2nd generation PS4 gold headset - and battery life isn’’t great anymore - is there a way to change it to new or upgrade it to higher capacity? Any advise will be appreaciated. This is the one I have: https://uk.pcmag.com/headphones/93785/so… Well, yes - figured it out by watching previous generation dissasembly - Battery is located on right side of the headset, so you need to take apart only that one....
Chosen Solution My phone was dropped and now the screen dose not work it turns on but screen doesnt light up and the screen is not cracked it has a small crack on the back can someone please help me Hi, Just because the screen is not cracked doesn’t mean that there isn’t an internal problem in the screen (e.g.broken connection) due to the fall. With the phone turned on, try shining a torch at an angle close to the screen and check if you can detect an image at all....
