Chosen Solution My p311 stinger Crossman is getting harder to reload it was working fine and suddenly got hard to reload You may want to try taking the slide off, checking that no parts have broken or BB’s have gotten wedged somewhere inside it. While apart, clean and oil it. my stinger just stopped working. it wont $!^& fully.
Chosen Solution Fitted a new battery, the home button cable came away from the top half (screen) section when prizing it up.. it’s still all in one piece and looked like the glue had just come away (was a small rectangular piece with tiny connecters in the middle) So now home button doesn’t work which may also be giving me this problem (as well as not being able to hold power and home button to reset / calibrate battery (from what i’ve read although other say the new battery doesn’t need calibrating....
Chosen Solution I bought a new screen and battery to repair an iPod Nano 6th Gen. I soldered in the battery and it said no charge, so I put it on the charger and the device turned on and I left it, but when I came back and removed from the charger it dies and says it needs to charge even though it shows a full battery and it is charging when I first plug it in....
Chosen Solution Will firmware updates to a Nikon D5000 be lost if defaulted to factory settings? No, this procedure has no effect on the firmware version. Thanks…. I thought that was it…. Looking for confirmation and it seems like I have it.
Chosen Solution I was in the middle of modding my ds but quickly stopped for noted reasons and know I reset my 3ds entirely to clear it, removed everything from the sd card and now my ehop has the error 007-2001. I wonder how you could fix this??? Hoi SlimSomething, To answer your question: Yes, the Nintendo eShop is Region-locked and is determined by both the Nintendo 3DS and the Nintendo Network ID used on the 3DS to access the shop, which is saved onto eShop servers....
Chosen Solution I Have a 2017 imac 21.5”, won’t turn on at all, no drives, no fans, nothing. I have taken the screen off and there are no diagnostic LEDs coming on at all. I have measured the voltages on the PSU as follows (all wrt the upper most pin on the larger connector: [larger connector] v ref 0v 0v 12.1v 12.1v 12.1v [smaller connector] 3.32v 0v 0.01v 0.02v 0v 0v does this indicate a dead PSU?...
Chosen Solution Here is my dilemma. I have a kohler cv18 command pro that has no spark. I have replaced the master wire harness (because is was butchered when I bought it), engine relay, coils, plugs, stator & the battery. I can’t figure it out. The only thing I haven’t tried is replacing the starter. Hi @ryan042204 , Here’s a link to the service manual for your engine, found on this webpage....
Chosen Solution Hi, I’ve just replaced a screen on an iPhone 5s. When I was reconnecting the last ribbon cable wouldn’t sit properly. I tried powering it up and now all I get is the Apple logo, then a blue screen and the phone will restart and repeat the process. I’m thinking I maybe shorted some pins together by mistake. Any ideas on how to get around this? I’ve reseated the battery and all over ribbon cables I can see but it’s still the same....
Chosen Solution I connect my blu advance 5.0 to my laptop and I cant find no file on it I had to manually install the USB driver in order to connect for my laptop to recognise and access my BLU Advance 5.0 hi, first you make sure that your operation system is actual (windows 8.1 or plus ) because this operations systems don’t have problems in this case . also, when you connect the phone in your laptop , in the top to the screen in your phone you can see a options to connectivity for usb, select the first (normally is for transfer files and others media files) and you can see the files in your laptop....
Chosen Solution Can’t find Onn brand in drop down so I place thus in tcl forum my apologies. Hi I purchased an onn 50 inch 4k tv model number ONA50UB19E05 in Jan of 2021 from walmart. Opted out of the warrenty stupid of me now the tv is failing. First the tv started flickering a black lines cutting in and Until one day it just did not turn on. The standby light was on but no response from the tv....
Chosen Solution Hi there I have a samsung 65 qled 4k purchased 2018 had a power outage stop working only thing is the ir light comes on then flashes couple of times,now I’ve researched and believed it was the powerboard so I replaced that still nothing then I removed the cable that connects the powerboard to the main board turn the power on and the backlight turns on and stays on,so it leaves me to think mainboard gone?...
Chosen Solution The printer won’t print an error screen comes up stating paper jam. I followed all therir instructions and still don’t see a paper jam. As the cartridges move aross it sounds like the gears are grinding on the right side. The reasons for this error can be different every time. Step 1 : Check thoroughly for even a small piece of paper might be stucked in the printer. Step 2 : Clean some of the gears inside the printer....
Chosen Solution I have a Boogie Board (model 01582801516) and in one of the corners there’s a large grey spot that won’t go away. Why is it like that? How can I fix it if it CAN be fixed? Actually, Found this: Boogie Board won’t erase sounds like screen burn in. and probably needs a new LCD. how long have you owned it? why does my boogie board have grey dots, WHY?...
Chosen Solution I dropped my phone a day ago accidentally. After drop in settings->battery->battery health it says it cant determine battery health. When I plugged it into charger it shows as charging but battery is stuck on %1 and it won’t go up. What’s broken? Battery, charging socket or motherboard? Hi @xoloth You should try a replacement battery. There is a protection circuit integrated into the battery which can fail causing weird problems....
Chosen Solution Hello. I have LG K10 i bought it new. I was plaing game when phone start to restart and its turn on and then again restart. Then it shows something like error ther was something like console i dont really know what was that. And last thing what i saw was " Jump to Dload Mode" and before was something like atemt killing the inic or somthing like that....
Chosen Solution My huawei mate 20 lite is stuck on logo and would not move forward. I have tried most things so far, I have used the power button which would turn it off, but as it switches on it wont go ahead of the huawei logo. I have tried power button with the volume up and volume down button, have tried all of that for many hours now. does anyone have a solutionto any of this....
Chosen Solution I have an iPhone 8. I just replaced the battery and lightning charger port assembly. After completing the replacements everything is working well; including each of the buttons. The one exception is that the Power Button on the right side of the phone is no longer responsive. I cannot turn my phone on or off with that button. Again, my phone wakes up and is useable with other buttons, and the screen goes dark once enough time has past....
Chosen Solution I have replaced the display (not for the faint of heart) and everything is working beautifully. However, I can not get the plastic strip to stick back on to cover the screws at the bottom. Do I need to buy a heat gun to melt the glue? I want it to look perfect. i used plastic super glue to fix mine about 2 months ago and its holding up beautifully....
Chosen Solution Are there any post battery replacement steps that should be followed, like charging the battery for couple of hours or charging and draining it and repeat 2-3 times. Thanks! I’d run it a full cycle: charge to 100% then allow to fully discharge. This will allow you to make sure that your battery is not defective and that the installation went properly.
Chosen Solution Hello everybody. I have tried to update my Macbook to Sierra as it was running a bit slot lately (the laptop is used mainly for movies, nothing too serious). After I got the error saying that it wasn’t possible to install the software, I tried to reinstall the OS from recovery mode. After a couple of times I got the PPM002 Error. Besides this, it only starts if I press and hold the power button until the Start Sound finishes....
