Chosen Solution So I was removing my old logicboard which had a bad headphone jack. And I bought a new one. I took it out of the iPad it came in tested it and everything. Worked fine. I put the iPad together set it up and it just stopped. And I was careful where I put everything. And handled the logicboard with care. Old logic board had headphone jack problem. That can be repaired....
Chosen Solution i got no picture but but sound and tv channels work. if i use a flash light on the screen i can slighty see whats going on, what to do next TV PHILIPS 49PUS6501 Hi Emil, Your backlight is most likely gone, so you need to get replacement LED strips and install them.
Chosen Solution So months ago did the SD upgrade - super easy, super great. Until…just the other day it died and would not respond at all. I have a couple ipods so I switched the battery (a known good working battery). Nothing. Got a different brand of CF to SD adapter cuz I read of them going bad. Got a different CF board. Nothing. It won’t power up, it won’t respond to reset, itunes does not recognize it....
Chosen Solution My device is not the first Wonderboom but the second, Wonderboom 2, could not find it as an device on here. When I try to turn it on it flashes red and makes the power down sound. When I connect it to charge nothing happens, no lights turning on, nothing. I’ve tried resetting it by holding down all the buttons but that did not work. I have contacted the support multiple times but I’m not even getting an answer from them even though I am covered by the warranty....
Chosen Solution My coffee is not hot enough for some reason. I’ve only had this one a few mths. Keurig Mini machines often have trouble brewing when used for the first time or after a long period of storage or cold exposure. It may be necessary to fill the tank and press “brew,” then wait about two hours before selecting the cup size to allow the machine to prime. The machine may require resetting if it shuts off before completing the brew cycle — simply lift the handle and close the K-Cup holder again to reset the system....
Chosen Solution Hello. Same problem with my MI3 after lcd repair. Motherboard must fix perfect in the frame. In my case was problem with left down corner (near antenna conector) Because of this also didnt work G sensor. Now everything works great Sooooo what is the question here my friend?
Chosen Solution Can you send me a blow up picture of my engine v-6 3.0 front wheel drive of my timing chain section in particular for me too see why my engine or if it is my oil leak according to my mechanic. That will cost me 900.00 in repair cost I already changed my main seal ,127.000mi.on engine thanks Main seal, is that the crankshaft seal in the timing cover?...
Chosen Solution I have a SHARP CD-XP200W player. The player worked just fine and a few days ago when I tried to turn it on, it only showed the “POWER ON” message and shut down. Now every time I try to turn it on it keeps happaning, Showing “POWER ON” and immediately shuts down. I checked the power supply and it all looks stable, my guess is something went wrong on the micro-proccessor from some mains power on / sudden power off but I have no clue what can it be… Anyone familier with this phenomenon?...
Chosen Solution So I had my phone in my uniform for a band show, pulled it out after and my screen was purple, pink, and green shades with lines and mixing of regular colors. It “was” limited to mainly the bottom portion of the screen. The background was still there but it was hard to see. Within the next 12 hours my phone screen began turning black before loosing 98% of the screen....
Chosen Solution hello can any one tell me is this screen original and if it is not original is oled quality or lcd quality ? hello tamer, its looks like Chinese copy, hard oled one. To be sure, look on sensor set loco.
Chosen Solution http://imgur.com/a/e5JML Here are some images of the screw holes, i just want another opinion if it could be long screw damage or not? Tried a new screen, its all black but i can hear when i connect the charger, so i googled a bit and it seemed like it could be long screw damage. Thanks By the look of the holes, there appears to be copper visable, which would indicate damage to the traces by the wrong screw being forced in, however its very hard to confirm without looking at it in person....
Chosen Solution I replaced both the cable assembly 1st (no change) then the button (no change). I have to assume the problem goes deeper than these 2 parts. need to get iphone charger part fix and try it damage problem but a charger on it to stay on
Chosen Solution I have an 20th anniversary PS4 controller that died. I was in the middle of using it and it just turned off and it will not charge or do anything. I have replaced the battery and the connection ribbon and that did not resolve the issue. I tried calling Sony and they will not fix it as it is out of warranty. I cannot simply replace this as a new one will cost $200+....
Chosen Solution Anytime my PS4 gets unplugged, or I lose power while it’s on, I basically lose all my stuff. It comes back up when I turn it back on and tries “check system storage.” It gets to 26% and stops every time. Then I get the prompt to download an update file onto a USB device and so forth. Had to do that numerous times in the past month, downloading all my games back, signing back in and everything....
Chosen Solution Hello, About a week ago, I changed the thermal paste and cleaned my PS4 CUH-1116A from dust, after testing that everything was OK, I completely forgot to fully test my BD drive, since the console didn’t have any visible problems with identifying any inserted game disk (it loads any previously installed game, probably can read the license off of the disc so that the game can start). However, a few days ago I tried another disk, that neither was used on that particular console nor have I ever played that game....
Chosen Solution My iPad screen is black, I tried hitting the home button and power button, it wants to come on but nothing. Please help try this solution, hold the reset button and the button on bottom of screen at same time for 10 or more seconds and it restarts…if don’t work you need to replace the screen, you can find the lcd on ifixit or you can find on third party
Chosen Solution Hi. I need some keys for my keeboard. I need the 4-key and the k-key. Where can i get it? This is the ‘4’ key http://www.ebay.com/itm/Macbook-Pro-Unib… and this is the ‘k’ key http://www.ebay.com/itm/Macbook-Pro-Unib… Hope this helps.
Chosen Solution There is a short on the board probably caused by trying to turn the phone on after water damage plus corrosion. You need a shop that can deal with fault finding and micro soldering.
Chosen Solution I have a Sansui tv picture went black but sound is perfect how can I fix it @cdooley2058 once you have the TV on a channel where you have sound, in a darkened room shione a flashlight at an angle against the screen. See if you can make out shapes etc. If so it is a bad backlight. If not then the possibility is a bad power board, a bad main board or a bad T-con board....
Chosen Solution So I’ve already swapped out power supplies and that did nothing. But then I tried putting a disc in and it beeped once. It didn’t pull the disc in but every time I slide it in again, it beeps once. Anyone recognize this symptom? The system is in great condition with zero signs of damage but before I do a complete tear down, any help is appreciated. Thanks...
